VERICUT Users' Forum
You are not logged in.
- Topics: Active | Unanswered
#1 2013-02-25 18:38:47
- Verifun
- Senior Member
- From: U.S.
- Registered: 2005-03-31
- Posts: 351
- Website
View spinning tool in the tool manager
Hi folks,
Because we have several multi-insert rotating tools, we would like CGTech to use within the tool manager the algorithm used to revolve tools in the machine simulation / workpiece view.
This is particularly helpful to people using Coro-U drills, multiple insert roughers, etc... (Like us)
Here we use toolman.bat to allow people to deal with VERICUT tool libraries without the need of a verification license... because of this, those people don't know if their tools are wrong until the NC-programmer complain about a tool that was wrongly defined... we want to allow the tool library guys (Our libraries are not maintained by the NC-Programmers) to see the result without going to a full verification license.
Since CGTEch already have the technology and code to do that within VERICUT verification, I think it's not a big deal for them to add this to the tool manager... :wink:
What do you think?
Daniel Santos
Offline
#2 2013-02-26 08:39:03
- Svante
- Senior Member
- From: Trollhättan, Sweden
- Registered: 2005-02-23
- Posts: 60
Re: View spinning tool in the tool manager
Agree! 
Svante Eriksson
System owner
GKN Aerospace Engine Systems Sweden
Vericut 7.2.1, 7.3.4, 7.4 - NX 9.0.3
Offline
#3 2013-02-26 12:41:11
- Chigishev
- Beta User
- From: Moscow, RUSSIA
- Registered: 2008-10-21
- Posts: 51
- Website
Re: View spinning tool in the tool manager
Good idea. It will be useful.
Offline
#4 2013-02-27 09:45:43
- Verifun
- Senior Member
- From: U.S.
- Registered: 2005-03-31
- Posts: 351
- Website
Re: View spinning tool in the tool manager
I think it can also help users to validate tool assemblies containing components that has the checkbox "Do Not Spin with Spindle" checked. Sometimes people forget to set that and you only see it during the simulation...
Daniel Santos
Offline
#5 2013-03-07 09:50:04
- paehv
- Senior Member
- From: Eindhoven, Netherlands
- Registered: 2005-01-17
- Posts: 160
- Website
Re: View spinning tool in the tool manager
Would be very usefull
Patrick Delisse
KMWE Aerospace - https://www.kmwe.com
(Vericut V9.4.1, Siemens NX2206, Campost)
Offline
#6 2013-03-22 18:13:39
- GregM
- Member
- From: Dallas/FtWorth, Texas
- Registered: 2005-08-25
- Posts: 19
Re: View spinning tool in the tool manager
I have to agree, it would be nice for the tool application engineer to be able to simulate the tool spinning so as to be able to tell if he selected the correct axis to rotate around. This could also be added to the "View" menu.
Offline
#7 2017-05-29 12:49:44
- Verifun
- Senior Member
- From: U.S.
- Registered: 2005-03-31
- Posts: 351
- Website
Re: View spinning tool in the tool manager
This is available in VERICUT 8.0.3 
Daniel Santos
Offline
#8 2017-08-29 22:01:21
- DaveF
- Senior Member
- From: Valencia, CA
- Registered: 2005-08-20
- Posts: 304
Re: View spinning tool in the tool manager
Nice!
Thanks Daniel for letting us know
Dave Frank
Aerospace Dynamics International, PCC
Valencia Ca
"Where else can you have this much fun,.......and get paid???."
Offline