VERICUT Users' Forum

Due to relentless spammers, we are no longer automatically accepting new forum registrations. If you wish to register for this forum, please send an e-mail to: info@cgtech.com

You are not logged in.

#1 2019-12-12 09:14:23

anorec
Member
Registered: 2014-12-16
Posts: 18

Vericut V9.0 and Spacepilot issue

I can't make work my 'support discontinued' 3Dconnexion SpacePilot with Vericut 9.0 (I have no issue with V8.2.2 though)

Is there a known way to fix that?

Offline

#2 2019-12-12 10:56:54

Vericut_McAtee
Senior Member
From: Fryeburg, Me.
Registered: 2011-07-17
Posts: 84

Re: Vericut V9.0 and Spacepilot issue

Following for I have the same SpacePilot, have not installed Vericut 9.0 yet, holding back a bit.

Offline

#3 2019-12-12 15:45:13

anorec
Member
Registered: 2014-12-16
Posts: 18

Re: Vericut V9.0 and Spacepilot issue

I called CGtech support and it seems it doesn't work anymore with old 3D Connexion drivers (10.4.xx and older).

Problem is last drivers doesn't work with legacy spacePilot...

Offline

#4 2019-12-23 18:53:32

blampman
Member
From: Milton, VT, USA
Registered: 2005-03-30
Posts: 14

Re: Vericut V9.0 and Spacepilot issue

We had the same problem with our discontinued SpaceExplorer. I updated to the latest driver for it from 3dconnexion and it worked, you may have to check their archives to find the older drivers.

Offline

#5 2019-12-29 08:03:49

anorec
Member
Registered: 2014-12-16
Posts: 18

Re: Vericut V9.0 and Spacepilot issue

SpaceExplorer is probably more recent than SpacePilot. As I said above mine doesn't work at all with last drivers (10.5 or 10.6) in Windows 7. Last official release is 3.16 however it works OK until 10.4.10 release (except with Vericut of course...)

Offline

#6 2019-12-30 07:52:47

stpendl
Senior Member
From: Nussbach, AUSTRIA
Registered: 2005-07-12
Posts: 134
Website

Re: Vericut V9.0 and Spacepilot issue

You can exchange your ancient SpacePilot at 3Dconnexion for a recent device.
We have done so at the time they were no longer officially supported.


Stefan Pendl

Systemmanager CAD/CAM
Windows 10 x64 Edition, Vericut 9.0

Offline

#7 2020-02-18 10:24:18

MSteinbruck
Member
Registered: 2016-07-21
Posts: 1

Re: Vericut V9.0 and Spacepilot issue

blampman wrote:

We had the same problem with our discontinued SpaceExplorer. I updated to the latest driver for it from 3dconnexion and it worked, you may have to check their archives to find the older drivers.

Hi,

we had the same problem with our SpaceExplorer USB. The latest available Version (10.6.4)  does not recognize it and the latest Version that supports it officially (10.4.3) is not supported by Vericut 9.

For future reference: Version 10.5.15 does work for us.

I did not test 10.6.0

Best regards
MSteinbruck

Offline

#8 2020-02-19 06:07:57

anorec
Member
Registered: 2014-12-16
Posts: 18

Re: Vericut V9.0 and Spacepilot issue

I tried a 10.5 major release with SpacePilot but it didn't work neither.
I don't remember minor release number i tried so i will retry 10.5.15. Anyway for now I went back to Vericut 8.2.2.3 for this issue and some others...

Last edited by anorec (2020-02-19 06:09:04)

Offline

Board footer