VERICUT Users' Forum
You are not logged in.
- Topics: Active | Unanswered
#1 2014-06-16 16:15:44
- a777starmy
- Member
- Registered: 2014-06-16
- Posts: 5
How to run M98 P***(sub program) in fanuc controller in vericut ??
my main program is 1st pic , sub program is 2nd pic
what shoud i do if i simulate in fanuc system ??
when i run it , it shows up alarm , and stop in first hole location
add word/address ??
Last edited by a777starmy (2014-06-16 16:17:57)
Offline
#2 2014-06-18 07:06:00
- wartron
- Member
- Registered: 2014-06-01
- Posts: 5
Re: How to run M98 P***(sub program) in fanuc controller in vericut ??
In the G-Code Processing toolbox,
M 98 (with P *) should set to "CallSub" Macro
P * (with M98 ) should set to "SubroutineName" Macro
O * should set to "SubroutineSequenceEnd" Macro
Offline
#3 2014-06-18 13:38:26
- a777starmy
- Member
- Registered: 2014-06-16
- Posts: 5
Re: How to run M98 P***(sub program) in fanuc controller in vericut ??
i am newbie
what should i do
can u show me step by step ??
thx a lot ^^
Offline
#4 2014-06-18 14:51:36
- MustaphaC
- VERICUT Specialist
- From: Le Mans, France
- Registered: 2004-10-14
- Posts: 130
- Website
Re: How to run M98 P***(sub program) in fanuc controller in vericut ??
If the sub-program is in a separate file, then you need to reference that file under "Sub-Programs" in project tree...
Mustapha
Offline
#5 2014-06-18 16:23:47
- a777starmy
- Member
- Registered: 2014-06-16
- Posts: 5
Re: How to run M98 P***(sub program) in fanuc controller in vericut ??
i have done but still have problem
like this
Last edited by a777starmy (2014-06-18 16:34:49)
Offline
#6 2014-06-19 08:11:06
- MustaphaC
- VERICUT Specialist
- From: Le Mans, France
- Registered: 2004-10-14
- Posts: 130
- Website
Re: How to run M98 P***(sub program) in fanuc controller in vericut ??
What error are you getting?
Mustapha
Offline
#7 2014-06-19 12:54:46
- a777starmy
- Member
- Registered: 2014-06-16
- Posts: 5
Re: How to run M98 P***(sub program) in fanuc controller in vericut ??
can not find sub program
Offline
#8 2014-06-20 06:38:34
- MustaphaC
- VERICUT Specialist
- From: Le Mans, France
- Registered: 2004-10-14
- Posts: 130
- Website
Re: How to run M98 P***(sub program) in fanuc controller in vericut ??
Not sure what's going on with your project? This is really basic thing which should work with no problem. Please send your project to your local CGTech represent. Thanks
Mustapha
Offline
#9 2014-07-21 18:48:56
- Selfywes
- Banned
- From: Croatia
- Registered: 2014-07-21
- Posts: 5
Re: How to run M98 P***(sub program) in fanuc controller in vericut ??
Hello .
Gorgeous here. I liked it! 
Offline
#10 2014-07-21 18:50:03
- Selfywes
- Banned
- From: Croatia
- Registered: 2014-07-21
- Posts: 5
Re: How to run M98 P***(sub program) in fanuc controller in vericut ??
Hellow .
Interestingly here. I liked it!
Offline
#11 2014-07-21 18:51:18
- Selfywes
- Banned
- From: Croatia
- Registered: 2014-07-21
- Posts: 5
Re: How to run M98 P***(sub program) in fanuc controller in vericut ??
Good afternoon.
Superbly here. I liked it!
Offline