VERICUT Users' Forum
You are not logged in.
- Topics: Active | Unanswered
Pages: 1
#1 2007-10-15 04:21:14
- mkahmann
- Member
- From: Luxembourg, Dudelange
- Registered: 2007-05-07
- Posts: 6
Cut Tolerance
How is the Cut Tolerance working on Detail?
I want to have information i.e. which values must I apply to be able to detect a defined amount of material in AUTODIFF.
If based on "Stock Size" is used as well a table would be good which reflects the "Cut Tolerance" according to the stock size.
At the moment it's very frustrating to set up the values. You can only do it by testing and testing and testing. Always with the risk to have a crash on machine (gouge/excess material which Vericut was not able to detect because the i.e. Cutting Tolerance was not set accurate enough).
Markus Kahmann
HUSKY
Offline
#2 2007-10-15 21:14:45
- DaveF
- Senior Member
- From: Valencia, CA
- Registered: 2005-08-20
- Posts: 304
Re: Cut Tolerance
Try Constant Gouge. It is independent of Cutting Tolerance, and will give you the exact reading in AUTODIFF you desire. Version 6.
Dave Frank
Aerospace Dynamics International, PCC
Valencia Ca
"Where else can you have this much fun,.......and get paid???."
Offline
#3 2009-05-29 09:00:24
- mkahmann
- Member
- From: Luxembourg, Dudelange
- Registered: 2007-05-07
- Posts: 6
Re: Cut Tolerance
Hello Dave,
well I asked for specific detailed information about Cutting Tolerance and not something else.... :?
Please read my tpic again an come back to me.
Regards
Markus
Markus Kahmann
HUSKY
Offline
#4 2010-10-06 18:16:59
- DaveF
- Senior Member
- From: Valencia, CA
- Registered: 2005-08-20
- Posts: 304
Re: Cut Tolerance
Check this out:
Bill Made a real good white paper on STL files
http://cgtech.com/forum/viewtopic.php?t … ht=polyfix
Dave
Dave Frank
Aerospace Dynamics International, PCC
Valencia Ca
"Where else can you have this much fun,.......and get paid???."
Offline
#5 2010-10-06 18:22:24
- DaveF
- Senior Member
- From: Valencia, CA
- Registered: 2005-08-20
- Posts: 304
Re: Cut Tolerance
Autodiff false Gouges
Dave Frank
Aerospace Dynamics International, PCC
Valencia Ca
"Where else can you have this much fun,.......and get paid???."
Offline
#6 2010-10-06 18:23:23
- DaveF
- Senior Member
- From: Valencia, CA
- Registered: 2005-08-20
- Posts: 304
Re: Cut Tolerance
constant gouge check
Dave Frank
Aerospace Dynamics International, PCC
Valencia Ca
"Where else can you have this much fun,.......and get paid???."
Offline
#7 2010-10-06 18:31:39
- DaveF
- Senior Member
- From: Valencia, CA
- Registered: 2005-08-20
- Posts: 304
Re: Cut Tolerance
Hello Dave,
well I asked for specific detailed information about Cutting Tolerance and not something else.... :?
Please read my tpic again an come back to me.
Regards
Markus
Markus
Sorry about the delay. I was pre-occupied at the time of you post, and then forgot about it.
take a look at the threads I posted here, and see if you have any more questions.
Autodiff
http://cgtech.com/forum/viewtopic.php?f … 4166#p4166
Dave
Dave Frank
Aerospace Dynamics International, PCC
Valencia Ca
"Where else can you have this much fun,.......and get paid???."
Offline
Pages: 1