Automatic Syntax checking upon simulation run

PBarna · 2013-11-13 17:50:14

:?: Hello everyone.
Is there a way to have Syntax checker automatically run upon simulation launch?
I have noticed that there is and has been a way to stop at tool changes, text, and so on but not because of Syntax errors.
(the predefined ones under Configurations>Word Format>Syntax Check....)
Maybe a script?

Thanks in advance
Phil

pawelwmn · 2013-11-17 12:33:53

Hello,

Why you want to do it during simulation?

In VERICUT you can go to the Analysis > Perform Syntax Check and then VERICUT will automatically scan all your NC Programs and find all errors- which you defined in Syntax Check tab - in them.

PBarna · 2013-11-18 14:43:35

pawelwmn wrote:

Hello,
Why you want to do it during simulation?
In VERICUT you can go to the Analysis > Perform Syntax Check and then VERICUT will automatically scan all your NC Programs and find all errors- which you defined in Syntax Check tab - in them.

Hello,
My point is to make it automated if you would like to.
To take out human error as mush as possible.
Plus if you check syntax before simulation, this is good. But if you make changes on the fly. Adding notes and such. Forget an end parenthetical statement or ?. Back up a few lines. Continue to simulate and it currently will not catch the mistake. Now if you remember to run the Syntax check again all is good.

I believe this would be a good addition to the current ways to have it stop simulation, tool change, ect. Like the image below. Or stick it in the pulldown.

Currently I am on 7.2.1
And I have spoke to support about this. They have been helping out. We will see.

Phil

pawelwmn · 2013-11-18 17:46:57

Hello,

OK, I agree with You, this feature can be a nice enhancement in new version of VERICUT software in such as cases as you wrote.

At this moment, maybe you can add a MessageMacro to G-Code Processing > Start of Processing > Global where you can write: "Remember to check syntax before close the VERICUT session" - it will show you in VERICUT Logger always when you put the reset button. Maybe this option can be useful for you

Pawel

PBarna · 2013-11-19 13:34:07

Great idea thanks.

PBarna · 2014-04-02 16:43:29

Installed 7.3.1 and cannot find anything just yet.
I hope they put it in there.

Tony · 2014-04-03 07:28:31

Did anyone enter an SCR ( software change request ) for this ?

MichaelS · 2014-04-04 15:06:48

This is a feature I am very interested in having.

Verifun · 2014-04-05 01:44:40

MichaelS wrote:

This is a feature I am very interested in having.

+10K

Tony · 2014-04-06 17:34:57

I'll make sure there is an SCR for this feature.

MichaelS · 2014-05-14 16:37:15

Bump.

Tony · 2014-05-14 16:48:22

There are several scr's for features relating to Syntax Check including Stop at Syntax Error, macros to start syntax checks etc

The more requests via your local Tech Support guys there are, the more likely it will get done.

MichaelS · 2014-05-15 15:42:49

Hallelujah!

VERICUT Users' Forum

#1 2013-11-13 17:50:14

Automatic Syntax checking upon simulation run

#2 2013-11-17 12:33:53

Re: Automatic Syntax checking upon simulation run

#3 2013-11-18 14:43:35

Re: Automatic Syntax checking upon simulation run

#4 2013-11-18 17:46:57

Re: Automatic Syntax checking upon simulation run

#5 2013-11-19 13:34:07

Re: Automatic Syntax checking upon simulation run

#6 2014-04-02 16:43:29

Re: Automatic Syntax checking upon simulation run

#7 2014-04-03 07:28:31

Re: Automatic Syntax checking upon simulation run

#8 2014-04-04 15:06:48

Re: Automatic Syntax checking upon simulation run

#9 2014-04-05 01:44:40

Re: Automatic Syntax checking upon simulation run

#10 2014-04-06 17:34:57

Re: Automatic Syntax checking upon simulation run

#11 2014-05-14 16:37:15

Re: Automatic Syntax checking upon simulation run

#12 2014-05-14 16:48:22

Re: Automatic Syntax checking upon simulation run

#13 2014-05-15 15:42:49

Re: Automatic Syntax checking upon simulation run

Board footer